Strömriktare 591P IP20 2Q 180A 500V Storlek 3 Armature

The Integrator series is a single family of both AC drives (AC690+) and DC drives (DC590+) offering the benefits of common programming, configuration and communication between both technologies. The DC590+ Integrator series' highly advanced DC drives fulfil the requirements of the most complex motor control applications. Comprehensive application software (including winding control as standard) together with function block programming and configurable I/O create a complete drive system in a single module.

Alternative:
- Programmable keypad 6901
- Communication technology box (Profibus-DP, DeviceNet, CANopen, LINK, LonWorks, EI Bisynch/RS422/RS485, Modbus RTU)
- Speed Feedback Technology Box (analogue tachometer, encoder microtach for acrylic fibre optics, microtach for glass fibre optics)
- EMC filters - industrial environment
- Linear actuators for European and North American markets (UL-CSA)
- Line inductors for long motor cables
- Stack Controller configuration with 598+ and 599+ available for retrofitting existing power stacks

Markets:
- Converting machines
- Plastics and rubber processing
- Wire and cable
- Metallurgical equipment
- Primary metal refining/process
- Pulp and paper
- Factory automation
- Vehicle

Features and benefits:
- Extremely easy installation and programming
- Extremely compact
- Removable keypad
- Motoristor input
- Stack Controller configuration with 598+ and 599+ available for retrofitting existing power stacks

Areas of use:
- Printout
- Cable machinery
- Film and foil lines
- Extrusion
- Mixers
- Annealing lines
- Slitting lines
- Metalworking
- Test benches
- Dynanometers

Macro function block:
- Open loop for winding control
- Winding control - load cell/dancer
- Section control
- Mathematical functions
- In-built control functions

Standards:
The DC590+ series DC drives listed on this page fulfil the following standards when installed in accordance with the relevant product manual:
- EMC compatibility: CE marked in accordance with 2004/108/EC (EMC Directive)
- Europe: This product complies with the Low Voltage Directive 2006/95/EC
- Safety: EN61800-5/2003 (when installed inside a cabinet)
- North America/Canada: *Meets UL508C and CSA22.2 #14 requirements as an open type drive (*applies to sizes 1-4 only)
- Overvoltage category: Overvoltage category III (three-phase supply) / Overvoltage category II (auxiliary supply)
- Degree of contamination: II (non-conductive contamination, except for occasional condensation) for control electronics

Technical specifications:
Power supply:
Trephases
110-220 V AC ± 10 %, 50-60 Hz ± 5 %
220-500 V AC ± 10 %, 50-60 Hz ± 5 %
500-690 V AC ± 10 %, 50-60 Hz ± 5 %

Current rating of the output luminaire:
15 - 1950A

Overloading:
- for 15 to 270A drivers: 150 % for 30 seconds / 200 % for 10 seconds
- for converters above 270A: see catalogue or manual for more information

Environment:
- for 15 to 165A drivers: 0-45°C / 32-113°F
- for 180 to 270A drivers: 0-35°C / 32-95°F
- for 380 to 1950A drivers: 0-40°C / 32-104°F
Up to 500 m above sea level (downgrade 1 % per 200 m up to a maximum of 5000 m)

Speed feedback:
- Armature voltage feedback / - Tachometer generator / - Pulse generator

Analogue inputs:
5 Total: 1 x 12 pieces (plus sign), 4 x 10 pieces (plus sign)
- 1x speed demand setpoint (-10/0/+10V) / 4x configurable

Analogue outputs:
3 Total: 10 pieces
- 1x Armature current output (-10/0/+10V or 0-10V) / 2x Configurable

Digital inputs:
9 Total: 24VDC (max 15mA)
- 1x Programme stop / 1x Unroll stop / 1x External stop / 1x Start-Run / 5x Configurable

Digital outputs:
3 Total: 24VDC / 100mA (short circuit protected)
- 3x configurable

Reference material:
- 1x- +10VDC / 1x -10VDC / 1x +24VDC

Power bridge:
590+ - 4 quadrant regenerative: Dual three phase SCR bridges
591+ - 2 Quadrant Non-regenerative: Single SCR bridge
Variable field control with SCRs

Drift protection:
- High energy MOVs / - Heat sink overtemperature / - Instantaneous overcurrent
- Thyristor fault / - Inverting time overcurrent / - Interline snubber network
- Field error / - Zero speed detection / - Speed feedback error / - Stop protection
- Overtemperature in the engine / - Stop protection

Additional information